ENC1000 User Guide - Revision history

Mparadis at 16:29, 1 June 2023

2023-06-01T16:29:45Z

← Older revision		Revision as of 16:29, 1 June 2023
Line 41:		Line 41:
	{{UGC-Firmware}}		{{UGC-Firmware}}
	{{UGC-Entry\|Setting IOMode\|\|		{{UGC-Entry\|Setting IOMode\|\|
	The ENC1000 can connect to any of the [https://www.phidgets.com/?tier{{=}}1&catid{{=}}4&pcid{{=}}2 encoders] we sell without any modification just by setting the {{Code\|IOMode}} property to '''Push-Pull''' . If you are trying to use your own encoder, you may need to change the IO mode to '''Open Collector''' or '''Line Driver''' mode. See the [[~~Encoder_Primer~~#Output_Circuit\|Encoder ~~Primer~~]] for more details on what to use.		The ENC1000 can connect to any of the [https://www.phidgets.com/?tier{{=}}1&catid{{=}}4&pcid{{=}}2 encoders] we sell without any modification just by setting the {{Code\|IOMode}} property to '''Push-Pull''' . If you are trying to use your own encoder, you may need to change the IO mode to '''Open Collector''' or '''Line Driver''' mode. See the [[Encoder_Guide#Output_Circuit\|Encoder Guide]] for more details on what to use.
	}}		}}

2022-01-17T21:14:34Z

← Older revision		Revision as of 21:14, 17 January 2022
Line 39:		Line 39:
	{{UGC-Graphing}}		{{UGC-Graphing}}
	{{UGC-DataInterval}}		{{UGC-DataInterval}}
			{{UGC-Firmware}}
	{{UGC-Entry\|Setting IOMode\|\|		{{UGC-Entry\|Setting IOMode\|\|
	The ENC1000 can connect to any of the [https://www.phidgets.com/?tier{{=}}1&catid{{=}}4&pcid{{=}}2 encoders] we sell without any modification just by setting the {{Code\|IOMode}} property to '''Push-Pull''' . If you are trying to use your own encoder, you may need to change the IO mode to '''Open Collector''' or '''Line Driver''' mode. See the [[Encoder_Primer#Output_Circuit\|Encoder Primer]] for more details on what to use.		The ENC1000 can connect to any of the [https://www.phidgets.com/?tier{{=}}1&catid{{=}}4&pcid{{=}}2 encoders] we sell without any modification just by setting the {{Code\|IOMode}} property to '''Push-Pull''' . If you are trying to use your own encoder, you may need to change the IO mode to '''Open Collector''' or '''Line Driver''' mode. See the [[Encoder_Primer#Output_Circuit\|Encoder Primer]] for more details on what to use.

2021-03-17T17:05:49Z

Explore Your Phidget Channels Using The Control Panel

← Older revision		Revision as of 17:05, 17 March 2021
Line 25:		Line 25:
	{{UGC-Start}}		{{UGC-Start}}

	{{UGC-Entry\|Encoder:\| Reads the signal of a quadrature encoder\|		{{UGC-Entry\|Quadrature Encoder Phidget:\| Reads the signal of a quadrature encoder\|
	In your Control Panel, double click on "Quadrature Encoder Phidget":		In your Control Panel, double click on "Quadrature Encoder Phidget":

2021-03-11T20:54:02Z

About

← Older revision		Revision as of 20:54, 11 March 2021
Line 10:		Line 10:
	===About===		===About===
	Interface with any 5V quadrature encoder with the Quadrature Encoder Phidget. With an encoder, you can keep track of how far your motor has turned, which then allows you to control the position and velocity in your code.		Interface with any 5V quadrature encoder with the Quadrature Encoder Phidget. With an encoder, you can keep track of how far your motor has turned, which then allows you to control the position and velocity in your code.

			[[Image:ENC1000_About.jpg\|link=\|700px]]

	===Explore Your Phidget Channels Using The Control Panel===		===Explore Your Phidget Channels Using The Control Panel===

2021-01-28T20:28:14Z

@@ Line 4: / Line 4: @@
 [[Category:UserGuide]]
 ==Part 1: Setup==
-{{UGIntro|ENC1000}}
+{{PT1 Deck Sequence}}
 == Part 2: Using Your Phidget ==

2021-01-06T20:45:50Z

Part 4: Advanced Topics and Troubleshooting

2020-07-31T19:17:13Z

2019-10-17T16:29:42Z

← Older revision		Revision as of 16:29, 17 October 2019
Line 31:		Line 31:
	{{ugAddressingInformation}}		{{ugAddressingInformation}}

	{{ugUsingYourOwnProgram\|~~This Phidget is compatible with the {{ExampleLink\|Encoder}}.~~}}		{{ugUsingYourOwnProgram\|ENC1000}}

	==Technical Details==		==Technical Details==

2018-08-28T16:11:10Z

Using the ENC1000

← Older revision		Revision as of 16:11, 28 August 2018
Line 31:		Line 31:
	{{ugAddressingInformation}}		{{ugAddressingInformation}}

	{{ugUsingYourOwnProgram\| the {{ExampleLink\|Encoder}}.}}		{{ugUsingYourOwnProgram\|This Phidget is compatible with the {{ExampleLink\|Encoder}}.}}

	==Technical Details==		==Technical Details==

2018-08-27T22:11:54Z

Using the ENC1000

← Older revision		Revision as of 22:11, 27 August 2018
Line 31:		Line 31:
	{{ugAddressingInformation}}		{{ugAddressingInformation}}

	{{ugUsingYourOwnProgram\| the {{ExampleLink\|Encoder}}}}		{{ugUsingYourOwnProgram\| the {{ExampleLink\|Encoder}}.}}

	==Technical Details==		==Technical Details==